Looking for the Best CNC Plasma Table?
In a rush? Check out the top pick here:
Baileigh CNC Plasma Cutting Table (PT-22)
- Runs on 110V power with 6A, 60HZ, and 24" x 24" cutting area (3/4" mild steel capacity)
- Comes fully assembled with correct alignment (no need to spend hours building)
- You can control the torch using the handheld panel with a jog dial for the X and Y axes and program start and stop buttons
- Durable, high-quality stepper motors drive the X axis (single drive) and Y axis (dual drive)
- All motor controllers and electronics are enclosed (no loose wires to get in your way)
Computerized numerical control, or more commonly known as CNC plasma cutters are the ones’ that are controlled automatically. In CNC plasma cutters, a jet operated with or without gas automatically cuts the material, similar to the design fed into its system.
Are you designing something super cool and worried about how to minimize the cutting time? To achieve your dream design without much effort and in minimal time, a CNC plasma cutter is all you need.
If you have fed up searching the best CNC plasma table and have not decided one yet. Then, we are here for you. After researching a lot about CNC plasma tables, we have come up with some of the top picks.
Best CNC Plasma Table: Our Top 6 Picks
1. Baileigh PT-22 CNC Plasma Cutting Table | Top Pick
Baileigh CNC Plasma Cutting Table (PT-22)
- Runs on 110V power with 6A, 60HZ, and 24" x 24" cutting area (3/4" mild steel capacity)
- Comes fully assembled with correct alignment (no need to spend hours building)
- You can control the torch using the handheld panel with a jog dial for the X and Y axes and program start and stop buttons
- Durable, high-quality stepper motors drive the X axis (single drive) and Y axis (dual drive)
- All motor controllers and electronics are enclosed (no loose wires to get in your way)
Arrives completely pre-assembled, Baileigh provides plenty of impressive features.
The best part of this table is the water bath. It has a sink with a valve; thus, you can easily avoid dust and smoke while working.
It comes with a design software package. Thus, you can design on your computer and load on it. It also supports USB cable.
As it does not have a downdraft system, it always provides a clean gas supply while working.
2. | Best Budget
If accuracy is most important for you, then must consider should be your preference.
It provides a significant room of 48 x 48 inches while working with the table’s overall size is 60 x 60 inches.
It is not only an affordable CNC plasma table but perfect for severe and deep cuts.
To ensure precise cuts, this plasma cutter table also provides torch height control. The drawback of this plasma cutter table is that it doesn’t have any cooling mechanism. Thus, stay extra careful while using the plasma cutter.
3. | Runner-Up
If size is a concern for you, then is what you are looking for. It is not just massive in size, but also comes packed with features.
With a plasma torch height, it ensures a perfect height in between the cutter and the material. Its plasma torch height is responsible for its precise cuts.
It has cutting dimensions 58 x 98 inches, which is a very large comparatively. It is a perfect heavy-duty plasma cutting table.
It also has StarCAM software to load your design into the table with a computer or a USB cable.
As it doesn’t have a water tank, it doesn’t avoid dust and dirt in the plasma cutter table.
4. Rbqlty CNC Plasma Table | Dual-Drive
If you want an excellent plasma table that can cut up to 10 mm thick material, is the ideal CNC plasma table you want.
With a dual-drive system, it provides very stable and precise cuts. Also, with its user-friendly interface, it is effortless to use this table.
Its affordable price makes it the best plasma table for money. With the CAD interface, you can easily design the cuts as per your requirement.
5. | Premium
comes with an automatic torch height cutter that provides exact cuts and a perfect height between the cutter and the material.
The most crucial feature in this plasma cutter is its in-built dust and fog vacuum system. It automatically cleans the dirt and extra fog from the plasma cutter table instead of a water bath.
Being medium-sized, this machine is ideal for a small workshop or personal purposes. It is 60-inch long and 120 inches wide.
Although, it doesn’t come pre-assembled, and thus you might require to invest some time to assemble this table as soon as you get it.
6. | Most User-Friendly
Are you looking for a versatile CNC plasma table? Then is all you need.
Along with an automatic torch height, it supports StarCAM software for designing the cut handily.
It is the best 4×4 plasma table that provides user-friendly buttons for its easy operation.
FAQs
Q: If I don’t know how to use a computer, will I still be able to operate the CNC plasma table?
A: Yes, it becomes pretty easy to operate the plasma tables because of their easy operation, user-friendly buttons, and user manual.
Q: On what all material can I use this plasma tables?
A: Almost all the CNC plasma tables can cut aluminum, mild steel, and stainless steel precisely. It matters on how thick the material is or how large it is size-wise.
Q: Who can use CNC plasma tables?
A: Whether you are a hobbyist or a professional, one can use the CNC plasma tables. With the latest technology trends, you are going to save a lot of time using it.
Q: How do I choose a plasma table?
A: Ideally, you want a clean, smooth edge that requires little further effort. With soft, clean cuts, improved plasma cutting systems produce a significantly smaller kerf (cut width), resulting in more precise cuts and less wasted metal. Additionally, it would be best if you considered reliability.
Q: How accurate is CNC Plasma?
A: CNC cutting machines of superior grade give significantly greater accuracy than plasma arc and oxy-fuel procedures. In general, the estimated accuracy for the high definition plasma cutting technique is rough +/-. 040” (material thickness dependent) and +/-. 125” for heavy plate oxy-fuel cutting.
Verdict
Now, you have enough scope to decide the specifications you want in a CNC plasma table and choose the one among them. But, if we were to choose, we think the Baileigh PT-22 CNC Plasma Cutting Table, given that it comes pre-assembled and has a superior design.
Plasma tables are worth purchasing as not only do they save your time, but provide the most accurate cuts in a single go.
Bestseller No. 1
Langmuir Systems - CrossFire CNC Plasma Table Bundle with Razor Weld 45 Cutter
- Crossfire Plasma Cutting Table with cut speeds up to 300 IPM - Featuring precise ball screw and stepper motor control accurite to 0.002" per 12"
- Razorweld 45 Plasma Cutter - 45 AMP, 1/2" Steel Cut Capacity, Plug N Play CNC Port, X45 Torch
- XL Expansion Kit (Included in Bundle) - Expands the cutting area to 24"x33"
- Water Table (Included in Bundle)
- Laptop Stand (Included in Bundle)
Bestseller No. 2
Langmuir Systems - CrossFire CNC Plasma Table Bundle
- Crossfire Plasma Cutting Table with cut speeds up to 300 IPM - Featuring precise ball screw and stepper motor control accurite to 0.002" per 12"
- XL Expansion Kit (Included in Bundle) - Expands the cutting area to 24"x33"
- Water Table (Included in Bundle)
- Laptop Stand (Included in Bundle)
- Limit Switch Kit (Included in Bundle)
Bestseller No. 3
STV Motorsports CNC Plasma Table - Made in the USA (SparX510-5x10)
- HIGH END TECHNOLOGY: The STV CNC Plasma Cutting Tables offer the best technology and high-quality components
- USED for MANY APPLICATIONS: Our CNC Plasma Cutting Machines works for a wide range of applications, using a Windows – based software (software package and license included0
- CONSISTENCY and SPEED: The STV CNC SPARX Series Plasma Tables are using high accuracy stepper motors for speed, control and smooth operation; it will offer you excellent consistency and speed
- VERY DURABLE and MADE in the USA: Our tables are built tough and designed to easily handle 3/4” steel plates (but they can handle more)
- LIFETIME SUPPORT PACKAGE: 1 Year Warranty and Lifetime Customer Support, Setup and Installation Support, Tutorials and Videos, How-to’s Manuals
Bestseller No. 4
Eastwood Versa-Cut 4'X4' CNC Plasma Table for Plasma Cutter Machine and Metal Cutting Torch Machines | Intuitive LCD Touch Screen Display with CNC Controller & USB Port | 33 Gal Waterbed Capacity
- MODERN TECHNOLOGY CNC PLASMA TABLE: Craft your unique metal design arts with unparalleled precision with the Eastwood Versa-Cut 4X4 CNC Plasma Table, a masterful blend of hobbyist accessibility and professional features. Crafted for those who demand perfection and a user-friendly metal fabrication experience. Designed specifically for use with Eastwood Versa-Cut 40 Plasma Cutter (Sold Separately).
- USER-FRIENDLY CNC CONTROLLER WITH INTUITIVE LCD DISPLAY INTERFACE: Our dedicated controller simplifies your metal fabrication operation, eliminating the need for external laptop computers. Preloaded with standard shapes and design patterns, This metal plasma cutting table also accepts custom CNC files through the built-in USB slot offering an intuitive and user-friendly interface for beginners and metal art hobbyist.
- SEAMLESS METAL CUTTING PRECISION: Experience unparalleled smoothness in metal cutting with the Eastwood Versa Cut 4X4 CNC Plasma Table. Robust stepper motors ensure long life and accurate cut movements, setting the stage for flawless craftsmanship. With a generous and adjustable height torch travel of 49.2" on the X-Axis and 43.3" on the Y-Axis, every intricate detail is brought to life with precision, making this set a benchmark for seamless and accurate metal fabrication.
- EASTWOOD QUALITY: Eastwood offers solutions which combines our 4,000+ unique products with the know-how to “Do The Job Right”. With an In-house product design, development and testing and a strong track record of high-quality, innovative products. Used and trusted by top builders to beginners and also provides a Lifetime Tech Support.
- SATISFACTION GUARANTEED: We stand behind our products with confidence. Our commitment to excellence ensures that your product is covered against defects. If you have any questions, please feel free to contact us, and our support team will provide answers within 24 hours.
Bestseller No. 5
Generic Plasma Green 9010 Plasma Table Additive
- Protects Plasma Cutting tables from rust & biological growth Vibrant Green Color Dilute to 5% by volume, or 20:1 ratio A 5 gallon pail will protect a 100 gallon volume table Compatible with all types of steel and aluminum Non-Hazardous, non-toxic, and bio-safe Will not leave mineralized or powdery deposits in table, water pan, slats, cutting tip, or consumables Plasma Green 9010 has been sold globally to industry, personal, automotive, schools, and military Manufactured in the US
Bestseller No. 6
STV Motorsports SparX505 5x5 CNC Plasma Cutting Table - Made in the USA
- HIGH END TECHNOLOGY: The STV CNC Plasma Cutting Tables offer the best technology and high-quality components
- USED for MANY APPLICATIONS: Our CNC Plasma Cutting Machines works for a wide range of applications, using a Windows – based software (software package and license included0
- CONSISTENCY and SPEED: The STV CNC SPARX Series Plasma Tables are using high accuracy stepper motors for speed, control and smooth operation; it will offer you excellent consistency and speed
- VERY DURABLE and MADE in the USA: Our tables are built tough and designed to easily handle 3/4” steel plates (but they can handle more)
- LIFETIME SUPPORT PACKAGE: 1 Year Warranty and Lifetime Customer Support, Setup and Installation Support, Tutorials and Videos, How-to’s Manuals
